Connect the Dediprog SF100 programmer to the system on which the Dediprog software is running. Connect the SF100 Dediprog Programmer with the 2x5 cable to the Intel Galileo Board.Ĥ. Remove all power supplies from the Intel Galileo motherboard, USB and power.ģ.
Download and install the Dediprog software.Ģ. An incorrect MAC address is not a problem, except when repairing two Intel Galileo motherboards using this method, which are connected to the same network.įollow the steps below to flash the new firmware onto your device.ġ. Note that changing the firmware using this method will result in an incorrect Mac address. The following things are required for this In this case you have to flash a new firmware. If you see the message "ASSERT_EFI_ERROR", the firmware is damaged.
To do this, connect a serial cable and open the BIOS. The following describes the process for repairing a bricked or unresponsive Intel Galileo board.Ĭheck whether your firmware is damaged before flashing new firmware on the Galileo board.
High speed programming: app 12 sec for 60 kb in serial mode with 16 MHz target clock for programming and verificationįlash programmer for STM8 series of flash microcontrollers with on-chip flashIf your Intel® Galileo board stops responding, you should check the Windows * com driver. Programs ST7 series of flash microcontrollers with on-chip flash Remote control functions for automated testersĪSCII command interface for automated programming Programming /Clearing/ Verifying / Read back supported High speed programmingĥ12 KByte internal Flash memory to store target program Programs Toshiba TLCS-870 and TMP91 series of flash microcontrollers The following microcontrollers are supported:
Once set up, Flasher can be controlled without the use of PC programĪSCII command interface to control Flasher without the use of PC program (Requires firmware version 1.84 or above) PC program allows batch mode processing for usage in automated test systems.
17 sec for 256 kb in serial mode with 10 MHz M16C target for programming and verification Programming / Verifying / Read back supportedĢMByte internal Flash memory to store target program It allows reading of program files in Motorola or Intel hex format. Programs M16C, M32C, R8C, R32C, M38000 and ST9 series of flash microcontrollers Support for RENESAS R8C/28, R8C29, M16C/64, M16C/65, M16C/6sįlasher comes with an easy to use Windows program. Serial Transfer Rate between J-Link and Target 500 mA if target is powered by Flasher ARM Programming speed between 30-300 Kbytes/second depending on target hardwareĭata files can updated as mass storage or via J-Flash Supports internal and external flash devicesĦ4 MB memory for storage of target programĬan be used as J-Link (JTAG emulator) with a download speed of up to 720 Kbytes/second No power supply required, powered through USB Stand-alone JTAG/SWD programmer (Once set up, Flasher can be controlled without the use of PC program) Flasher ARM connects via USB or via RS232 and has a built-in 20-pin JTAG connector, which is compatible with the standard 20-pin connector defined by ARM. In addition to that Flasher ARM has all of the J-Link functionality. Flasher ARM is designed for programming flash targets with the J-Flash software or stand-alone. Programming tool for STM8 series of flash microcontrollersįlasher ARM is programming tool for microcontrollers with on-chip or external Flash memory and ARM core.
Programming tool for ST7 series of flash microcontrollers Programming tool for Toshiba TLCS-870 series of flash microcontrollers and TMP91 in serial mode (1.5 MByte FLASH to store target program, remote control functions for automated testers) Programming tool for ST9 and Renesas M16C/20, M16C/62, M16C/80, M32C, R8C, R32C, M38 and M79 series of flash microcontrollers in serial mode
Programming tool for microcontrollers with on-chip or external Flash memory and ARM core Flasher connects via USB or via RS232 interface to a PC, running Microsoft Windows There are several flashers to cover ARM, M16C, M32C, R8C, R32C, M38000, ST9, Toshiba TLCS-870 and TMP91, ST7 and STM8 Flasher is designed for programming flash targets stand-alone.
Flash Programming tools for micro controllers with on-chip or external Flash memory and core memory.